#FLOPPY TO USB EMULATOR SOFTWARE INSTALL#

I can't install the USB Floppy Format Tool. It did this all the way up to 73, and at 74 it asked me if I wanted to format the disk. When I selected 001 on the stick, the PSR again displayed CHECKING, then it displayed the P1 tab, but no styles. The PSR first displayed CHECKING, then displayed a P1 tab and all of the 1.2MB worth of styles that I had copied to the stick. Then I copied 1.2MB worth of STY files from the computer to the root level of the stick and put the stick back into the PSR. I was expecting to see several folders, but there weren't any. The only thing that was on the stick was SYSTEM VOLUME INFORMATION.

#FLOPPY TO USB EMULATOR SOFTWARE WINDOWS 10#

So I removed the stick from the PSR and stuck it into my Windows 10 computer to have a look at what was on it. The PSR display was blank, but at least the PSR did not display DISK ERROR! Next, I pressed 'D' on the PSR, then NEXT until the Floppy tab was highlighted.

Then I released the 2 buttons and the emulator displayed 000. After holding the 2 buttons down for 3 minutes I managed to get the emulator to flash 00 through 36 during one of the sequences. The emulator continued flashing the sequence several more times, then flashed 00 through 10, then again flashed the sequence several more times. The emulator quickly flashed a sequence of U01, then 126, then F01, repeated that a few times, and then flashed 00 thru 10. I inserted the stick into an unpowered PSR2000, then held the emulator's 2 buttons down while I turned the PSR on. So I went ahead and used the Self Format function of the emulator. When I unzipped version 1.2 and looked at its files I did not see any EXE or MSI or other installation files, so I was not able to install the Floppy Format Tool. I don't know what that was all about, so I just ignored it.Р В РІР‚СњР В РІР‚С›nyway, I did manage to download version 1.2, of the USB Floppy Format Tool for the USB but I can't recall from where. It talked about connecting the emulator to the computer's USB port and partition 'it' to 100 floppies.

#FLOPPY TO USB EMULATOR SOFTWARE PDF#

I also opened the PDF that one you attached to your reply. I did this using first Firefox and then using Internet Explorer, so I assume that the company is no longer in business? I also tried '' but no luck there either. It also says this is available at but when I go there all I get is a 'Problem Loading Page, Unable to connect' message. The video talks about downloading USB Floppy Format Tool for the USB Floppy Emulation V2, revision 1.40i'. I opened the link you provided and viewed the video. In any event, perhaps somebody else could chime in with a handy hint? From what I gather, you must format the USB stick on a PC and when you do you will then have either 100 (old one) or 1000 (new one) 'FDs' on it.

#FLOPPY TO USB EMULATOR SOFTWARE SOFTWARE#

I looked on the internet but couldn't find any software that might be usable, and I don't recall anybody else on this forum stating he or she had to do anything with the emulator other than connect it and use it.

No instructions and no software disk came with either emulator. It would be nice to know just where to put the jumpers on the new emulator. The newer one has fewer components on its PCBA, a PCBA that differs from the one in the older emulator, has a 3-digit display, has two jumpers on it (one across S1 and one across J5 and JA), has no red button on it, and it came in a black case. The older one has more components on its PCBA, has a 2-digit display, has only one jumper on it (that is connected to only one pin), has a different green LED setup, has a red push-push button on it below the green LED, and came in a cream-colored case. I have a hunch that the 'A' is a revision to the model #. Nowhere is there any sticker or other marking stating the model number. I also had a look under the hood of the one I just bought. I just checked the emulator that I bought in 2012 and the sticker on it reads 'SFR1M44-U100'.

Floppy to usb emulator software